Trusted by Clinton property owners for heat pump repair, AC service, furnace maintenance & complete HVAC installation throughout Michigan.
NATE-certified technicians providing the complete range of heating and cooling services.
A professionally installed mini-split eliminates the energy losses associated with traditional ductwork while providing independent temperature control per zone. Technicians mount indoor heads at optimal height, route linesets with proper insulation, and commission each zone for verified heating and cooling output.
A correctly sized heat pump installation eliminates the guesswork of mismatched equipment and undersized ductwork. Our technicians perform load calculations, verify airflow across the evaporator coil, and commission the system to manufacturer specifications for peak efficiency and longevity.
Ductwork problems manifest as uneven room temperatures, excessive dust near registers, and HVAC systems that run continuously without satisfying the thermostat. Technicians identify crushed flex runs, separated joints, and deteriorated mastic seals using pressure testing and visual inspection protocols.
Restoring heat pump performance starts with accurate diagnostics of compressor function, reversing valve operation, and refrigerant charge levels. Our NATE-certified technicians service all major brands including Carrier, Trane, Lennox, and Rheem to resolve airflow loss, short cycling, and defrost failures.
A comprehensive furnace tune-up includes combustion analysis, heat exchanger inspection, and verification of gas pressure at the manifold. Technicians clean burners, test flame sensor microamp readings, and confirm proper flue draft to maintain safe, efficient operation throughout the heating season.
Professional AC tune-ups follow a multi-point inspection protocol covering thermostat calibration, condensate drain clearing, electrical connection tightening, and evaporator coil cleaning. Maintaining clean coils and proper superheat readings keeps your system running at peak rated efficiency.
Air conditioning failures range from simple capacitor replacements to complex compressor and refrigerant circuit repairs requiring EPA Section 608 certified handling. Our technicians diagnose the root cause using superheat and subcooling measurements, amp draws, and pressure readings to restore full cooling output.
Full HVAC installation requires coordination of heating equipment, cooling components, ductwork design, and control systems to deliver efficient comfort at rated capacity. Our technicians perform Manual J and Manual D calculations, size equipment to match your structure, and commission the system to manufacturer standards.
Clogged dryer vents are a leading cause of residential fires, with lint buildup restricting exhaust airflow and causing the dryer to overheat. Professional cleaning removes compacted lint from the full vent run, verifies proper airflow velocity, and inspects the exterior termination for damage.
Boiler systems demand specialized knowledge of hydronic circuits, expansion tanks, pressure relief valves, and combustion analysis. Our technicians diagnose issues ranging from kettling and low water pressure to faulty zone valves and circulator pump failures across gas, oil, and electric units.
Clean ductwork directly impacts the efficiency of your HVAC system by reducing static pressure and allowing unrestricted airflow to every register. Our technicians inspect for microbial growth, seal access points after service, and verify airflow improvements with anemometer readings post-cleaning.
Comprehensive HVAC inspections cover thermostat operation, ductwork condition, refrigerant levels, electrical connections, and combustion safety. This detailed assessment identifies efficiency losses, safety hazards, and components nearing end of service life before they result in costly emergency repairs.
When a mini-split displays error codes, produces weak airflow, or fails to reach setpoint, the fault often lies within the inverter board, thermistor sensors, or refrigerant circuit. Professional repair restores rated SEER output and eliminates the inefficient short cycling that drives up utility costs.
Smart thermostats from Ecobee, Nest, and Honeywell Home offer occupancy sensing, geofencing, and learning algorithms that adapt to your schedule automatically. Our technicians verify system compatibility, install the required wiring, and configure the device for optimal interaction with your specific HVAC equipment.
HVAC emergencies do not follow business hours, and a failed system in extreme temperatures puts your household at risk. Our technicians carry common replacement parts including capacitors, contactors, ignitors, and fan motors to resolve most failures in a single visit and restore comfort fast.
A city of 103,429 residents generates significant demand for emergency HVAC services, especially during extreme weather events and seasonal transitions when systems are stressed to their limits. KIC Refrigeration maintains the crew capacity, parts inventory, and dispatch infrastructure to respond to multiple emergencies simultaneously across Clinton when conditions demand it.
We have responded to every type of HVAC emergency across Clinton, and that experience informs every diagnostic decision we make on-site. From compressor failures and heat exchanger cracks to frozen evaporator coils and tripped high-limit switches, our techniques are optimized for the equipment brands, duct configurations, and climate demands that Clinton systems face year after year.
What makes us different from every other heating and cooling company in the area.
You receive a written estimate with itemized parts and labor costs before any work begins, and the final invoice matches. No diagnostic fees hidden in the repair bill, no surprise surcharges — just honest pricing you can verify and trust.
Every technician carries EPA Section 608 Universal certification for refrigerant handling — required by federal law for working with R-410A, R-22, R-32, and all regulated refrigerants. Your system is serviced by technicians who handle refrigerants legally and responsibly.
Every technician on our team holds current NATE certification — the highest standard in the HVAC industry for installation and service competency. You get a technician who has passed rigorous exams on system diagnostics, refrigerant handling, and equipment commissioning.
We carry full general liability and workers compensation coverage on every job. Our HVAC license is current in every state we operate, and we pull permits when local codes require them. Your property and our crew are fully protected on every visit.
HVAC failures do not wait for business hours and neither do we. Our emergency technicians are dispatched around the clock — nights, weekends, and holidays — so you never go without heat in winter or cooling in the peak of summer.
Common questions about HVAC service, costs, and what to expect when you call.
Heat pumps offer both heating and cooling from a single outdoor unit, making them significantly more energy-efficient than furnaces for moderate climates. A heat pump does not generate heat — it transfers it from outdoor air, which requires far less energy than burning gas or running electric resistance coils. Modern cold-climate heat pumps with variable-speed inverter compressors operate effectively down to minus 15 degrees Fahrenheit, making them viable in most Michigan locations. For Clinton homeowners with natural gas access, a dual-fuel system — heat pump for primary heating paired with a gas furnace for backup during extreme cold — often provides the best balance of efficiency and performance. Heat pumps also qualify for federal tax credits under the Inflation Reduction Act. KIC Refrigeration evaluates your specific climate zone, insulation levels, and utility rates to determine whether a heat pump, furnace, or dual-fuel system is the smartest investment.
Most HVAC installations, major equipment replacements, and significant ductwork modifications in Clinton require a mechanical permit from the local building department. This applies to furnace and air conditioner replacements, heat pump installations, boiler swaps, and new ductless mini split systems. Minor repairs like part replacements and refrigerant recharges typically do not require permits. KIC Refrigeration handles all permitting, code compliance documentation, and scheduling of final inspections on your behalf — you do not need to visit any government office or coordinate with inspectors. Permits exist to ensure your system is installed safely and to code, which protects your home and preserves your equipment warranty. Unpermitted work can create liability issues and complicate future home sales. We ensure every project meets current Michigan mechanical codes and International Mechanical Code standards.
Yes. KIC Refrigeration provides around-the-clock emergency heating and cooling repair throughout Clinton and surrounding Michigan communities. Whether your furnace fails during a cold snap and pipes are at risk of freezing, your air conditioner dies during a dangerous heat wave, or you detect the smell of gas near your equipment, our technicians respond quickly. Every service vehicle carries common replacement parts — capacitors, contactors, ignitors, blower motors, control boards, and refrigerant — so most emergency repairs are completed in a single visit. We do not charge extra trip fees for after-hours calls, and our dispatchers are trained to triage situations over the phone so the right technician arrives with the right equipment. Call us anytime and we will have a crew on the way.
Absolutely. Modern high-efficiency HVAC equipment can reduce heating and cooling costs by 20 to 40 percent compared to systems installed 15 or more years ago. The improvement comes from advances in compressor technology, variable-speed motors, and smarter controls. In Clinton, upgrading from a 10-SEER air conditioner to a 16-SEER2 or higher unit delivers substantial monthly savings — the higher the SEER2 rating, the less electricity consumed per BTU of cooling. On the heating side, replacing an 80-percent AFUE furnace with a 96-percent modulating furnace means that 16 cents of every heating dollar previously wasted up the flue now heats your home. Heat pumps offer even greater efficiency, delivering 2 to 4 times more heating energy than they consume in electricity. KIC Refrigeration calculates projected energy savings for any equipment upgrade so you can see the return on investment before making a decision.
A comprehensive HVAC inspection from KIC Refrigeration in Clinton covers every critical component of your heating and cooling system. Our NATE-certified technician evaluates the heat exchanger for cracks using a combustion analyzer, checks thermostat calibration and wiring, tests all electrical connections for tightness and amperage draw, measures refrigerant pressures against manufacturer specifications, clears the condensate drain line, inspects the blower motor and fan assembly for wear, checks the air filter and evaporator coil condition, tests safety controls including high-limit switches and flame sensors, performs carbon monoxide testing on gas-burning equipment, and measures supply and return airflow temperatures to verify the system is producing its rated BTU output. We also visually inspect accessible ductwork for leaks, damage, and insulation condition. You receive a written report with all findings, photos of any concerns, and prioritized recommendations.
Most residential HVAC installations in Clinton, MI are completed in 1 to 3 days depending on the system type, condition of existing ductwork, and complexity of the project. A straightforward furnace and air conditioner replacement on existing ductwork typically takes a single day — our crews arrive in the morning and commission the new system by afternoon. Heat pump conversions, ductless multi-zone installations with line sets routed through walls, and projects requiring new or modified ductwork may take 2 to 3 days. Commercial installations and whole-building systems can extend to a week. We schedule around your availability, coordinate all permits and inspections, and protect your flooring and walls throughout the process. Every installation concludes with a full system commissioning including airflow verification and refrigerant charge confirmation.
Real feedback from homeowners and property managers who trust us with their comfort.
"KIC Refrigeration installed our whole-home HVAC system during the renovation. They coordinated perfectly with our contractor and stayed on schedule."
"KIC Refrigeration repaired our heat pump when two other companies said it needed full replacement. Saved us thousands. Still running great six months later."
"AC tune-up before summer. Technician was early, finished in about forty-five minutes, and gave me a clean bill of health on the system. Easy process."
We also serve these nearby communities with the same certified HVAC expertise.